• Skip to primary navigation
  • Skip to main content
CVE Vulnerability

CVE Vulnerability

  • CVE’s
  • Products
  • Vendors

CVE-2018-0056

February 26, 2023 by

If a duplicate MAC address is learned by two different interfaces on an MX Series device, the MAC address learning function correctly flaps between the interfaces. However, the Layer 2 Address Learning Daemon (L2ALD) daemon might crash when attempting to delete the duplicate MAC address when the particular entry is not found in the internal MAC address table. This issue only occurs on MX Series devices with l2-backhaul VPN configured. No other products or platforms are affected by this issue. Affected releases are Juniper Networks Junos OS: 15.1 versions prior to 15.1R7-S1 on MX Series; 16.1 versions prior to 16.1R4-S12, 16.1R6-S6 on MX Series; 16.2 versions prior to 16.2R2-S7 on MX Series; 17.1 versions prior to 17.1R2-S9 on MX Series; 17.2 versions prior to 17.2R1-S7, 17.2R2-S6 on MX Series; 17.3 versions prior to 17.3R2-S4, 17.3R3-S1 on MX Series; 17.4 versions prior to 17.4R1-S5 on MX Series; 18.1 versions prior to 18.1R2 on MX Series.

CVE-2018-0055

February 26, 2023 by

Receipt of a specially crafted DHCPv6 message destined to a Junos OS device configured as a DHCP server in a Broadband Edge (BBE) environment may result in a jdhcpd daemon crash. The daemon automatically restarts without intervention, but a continuous receipt of crafted DHCPv6 packets could leaded to an extended denial of service condition. This issue only affects Junos OS 15.1 and later. Earlier releases are unaffected by this issue. Devices are only vulnerable to the specially crafted DHCPv6 message if DHCP services are configured. Devices not configured to act as a DHCP server are not vulnerable to this issue. Affected releases are Juniper Networks Junos OS: 15.1 versions prior to 15.1R7-S2; 15.1X49 versions prior to 15.1X49-D160; 15.1X53 versions prior to 15.1X53-D235, 15.1X53-D495; 16.1 versions prior to 16.1R4-S11, 16.1R6-S6, 16.1R7-S2; 16.2 versions prior to 16.2R2-S7; 17.1 versions prior to 17.1R2-S9; 17.2 versions prior to 17.2R2-S6; 17.3 versions prior to 17.3R3-S1; 17.4 versions prior to 17.4R1-S5; 18.1 versions prior to 18.1R2-S3; 18.2 versions prior to 18.2R1-S2; 18.2X75 versions prior to 18.2X75-D20.

CVE-2018-0054

February 26, 2023 by

On QFX5000 Series and EX4600 switches, a high rate of Ethernet pause frames or an ARP packet storm received on the management interface (fxp0) can cause egress interface congestion, resulting in routing protocol packet drops, such as BGP, leading to peering flaps. The following log message may also be displayed: fpc0 dcbcm_check_stuck_buffers: Buffers are stuck on queue 7 of port 45 This issue only affects the QFX5000 Series products (QFX5100, QFX5110, QFX5200, QFX5210) and the EX4600 switch. No other platforms are affected by this issue. Affected releases are Juniper Networks Junos OS: 14.1X53 versions prior to 14.1X53-D47 on QFX5000 Series and EX4600; 15.1 versions prior to 15.1R7, 15.1R8 on QFX5000 Series and EX4600; 15.1X53 versions prior to 15.1X53-D233 on QFX5000 Series and EX4600; 16.1 versions prior to 16.1R7 on QFX5000 Series and EX4600; 16.2 versions prior to 16.2R3 on QFX5000 Series and EX4600; 17.1 versions prior to 17.1R2-S9, 17.1R3 on QFX5000 Series and EX4600; 17.2 versions prior to 17.2R2-S6, 17.2R3 on QFX5000 Series and EX4600; 17.2X75 versions prior to 17.2X75-D42 on QFX5000 Series and EX4600; 17.3 versions prior to 17.3R3 on QFX5000 Series and EX4600; 17.4 versions prior to 17.4R2 on QFX5000 Series and EX4600; 18.1 versions prior to 18.1R2 on QFX5000 Series and EX4600.

CVE-2018-0053

February 26, 2023 by

An authentication bypass vulnerability in the initial boot sequence of Juniper Networks Junos OS on vSRX Series may allow an attacker to gain full control of the system without authentication when the system is initially booted up. Affected releases are Juniper Networks Junos OS: 15.1X49 versions prior to 15.1X49-D30 on vSRX.

CVE-2018-0052

February 26, 2023 by

If RSH service is enabled on Junos OS and if the PAM authentication is disabled, a remote unauthenticated attacker can obtain root access to the device. RSH service is disabled by default on Junos. There is no documented CLI command to enable this service. However, an undocumented CLI command allows a privileged Junos user to enable RSH service and disable PAM, and hence expose the system to unauthenticated root access. When RSH is enabled, the device is listing to RSH connections on port 514. This issue is not exploitable on platforms where Junos release is based on FreeBSD 10+. Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D77 on SRX Series; 12.3 versions prior to 12.3R12-S10; 12.3X48 versions prior to 12.3X48-D75 on SRX Series; 14.1X53 versions prior to 14.1X53-D47 on QFX/EX Series; 15.1 versions prior to 15.1R4-S9, 15.1R6-S6, 15.1R7; 15.1X49 versions prior to 15.1X49-D131, 15.1X49-D140 on SRX Series; 15.1X53 versions prior to 15.1X53-D59 on EX2300/EX3400 Series; 15.1X53 versions prior to 15.1X53-D67 on QFX10K Series; 15.1X53 versions prior to 15.1X53-D233 on QFX5200/QFX5110 Series; 15.1X53 versions prior to 15.1X53-D471, 15.1X53-D490 on NFX Series; 16.1 versions prior to 16.1R3-S9, 16.1R4-S9, 16.1R5-S4, 16.1R6-S4, 16.1R7; 16.2 versions prior to 16.2R2-S5; 17.1 versions prior to 17.1R1-S7, 17.1R2-S7, 17.1R3; 17.2 versions prior to 17.2R1-S6, 17.2R2-S4, 17.2R3; 17.2X75 versions prior to 17.2X75-D110, 17.2X75-D91; 17.3 versions prior to 17.3R1-S4, 17.3R2-S2, 17.3R3; 17.4 versions prior to 17.4R1-S3, 17.4R2; 18.2X75 versions prior to 18.2X75-D5.

CVE-2018-0051

February 26, 2023 by

A Denial of Service vulnerability in the SIP application layer gateway (ALG) component of Junos OS based platforms allows an attacker to crash MS-PIC, MS-MIC, MS-MPC, MS-DPC or SRX flow daemon (flowd) process. This issue affects Junos OS devices with NAT or stateful firewall configuration in combination with the SIP ALG enabled. SIP ALG is enabled by default on SRX Series devices except for SRX-HE devices. SRX-HE devices have SIP ALG disabled by default. The status of ALGs in SRX device can be obtained by executing the command: show security alg status Affected releases are Juniper Networks Junos OS: 12.1X46 versions prior to 12.1X46-D77; 12.3X48 versions prior to 12.3X48-D70; 15.1X49 versions prior to 15.1X49-D140; 15.1 versions prior to 15.1R4-S9, 15.1R7-S1; 15.1F6; 16.1 versions prior to 16.1R4-S9, 16.1R6-S1, 16.1R7; 16.2 versions prior to 16.2R2-S7, 16.2R3; 17.1 versions prior to 17.1R2-S7, 17.1R3; 17.2 versions prior to 17.2R1-S6, 17.2R2-S4, 17.2R3; 17.3 versions prior to 17.3R1-S5, 17.3R2-S2, 17.3R3; 17.4 versions prior to 17.4R2. No other Juniper Networks products or platforms are affected by this issue.

  • « Go to Previous Page
  • Go to page 1
  • Interim pages omitted …
  • Go to page 5078
  • Go to page 5079
  • Go to page 5080
  • Go to page 5081
  • Go to page 5082
  • Interim pages omitted …
  • Go to page 18763
  • Go to Next Page »

Copyright CVE Vulnerabilities 2023
Data Sources:

  • NIST
  • MITRE
  • CVE Search
  • Open CVE